Manual.ly Logo

Vitavia Ida 3300 Bruksanvisning

0,0 · 0 Vurderinger

PDF-manual · 36 sider

Nynorsk

M: OA-GPT-5-NAN
side

/ 36

Loading...
abc5ec3926869db49e35420105f806883818 page 4
4
Assembly Instructions
Safety Warning
SITE SELECTION
Always try to select a sunny location, sheltered
from the wind as much as possible.
IMPORTANT
Before assembling your new greenhouse,
please check that all parts in the provided list
are included. Please take each bundle out of
the packaging in order to identify the parts
better.
It is important that the opened bundles do not
get mixed with one another.
If something is missing please contact your
retailer.
Nuts (1002) - Max. tightening torque 3Nm.
NECESSARY TOOLS
Screw drivers (Normal and Crosshead PH2),
10 mm socket spanner or wrench, 10 mm
combination spanner, knife, measuring stick,
spirit level, Accu-drill with adjustable torque.
MAINTENANCE
The greenhouse should be thoroughly washed
with a gentle detergent occasionally. Please
check that the detergent used does not react
aggressively with aluminium or the glass xing
clips.
Ensure that the upper and lower door tracks
are cleaned regularly to avoid a build up of
debris.
0. BASE
Important! The base must be exactly square
and level. A zinc-coated steel base is available
as an accessory for all greenhouse models.
(Attention! Only when the greenhouse has to
be located in a very windy and unprotected
location: Drill through both the prole at the
base of the greenhouse and the steel base,
and connect them with nuts and bolts.)
If you would rather construct your own stone
or concrete foundation, please follow the
dimensions specied in diagram 0. Treated
wooden beams at least 18 mm high and not
more then 32 mm wide should be positioned
between the stone/concrete foundation and
the aluminium frame, and connected to the
foundation with 50 mm long bolts (not
provided).
Foundations must extend down below the frost
level.
Diagrams in a single frame show the view
from inside the greenhouse. Those
enclosed in a double frame show the view
from outside the greenhouse.
1. FRONT
Lay all of the parts on the oor and connect
them loosely.
Loosely connect the corner plates (1092) on
the upper corners.
2. ASSEMBLY
Connect the gable end bars (4086 / 4087)
between the eaves door track (4090) (2.1) and
the vertical wall bars (4088 / 4089) (2.3). Now
connect the ridge bar (4052) (2.3) and then sill
bars (1022) (2.4 & 2.5).
Loosely connect the corner plates (1092)
above the eaves (2.1) and at the roof ridge
(2.3).
Connect the side glazing bars (4091 / 4092),
including two extra bolts in each glazing bar.
Connect side braces (4094).
Connect the roof glazing bars (4056) between
the eaves (2.2) and the ridge bar (2.3).
Please use the washers (7395) at all
connection points to eaves door track (4090)
(2.1 & 2.2).
It is necessary to include one extra bolt in the
glazing bars (4056) at this point, to later
connect the roof vent.
3. ASSEMBLY ON WALL
Now position your greenhouse on the
prepared base/foundation and connect loosely.
Adjust the greenhouse until it is completely
square and tighten all bolts.
Please do not over tighten. (max. 3Nm)
Ensure that the sides are perfectly vertical.
Note the pre-drilled holes in the vertical wall
bars (4088 / 4089)) and ridge bar (4052) and
mark them on the wall.
Remove the frame from the base.
Drill 6 mm holes in the wall as marked and
place 6mm wall plugs in the wall.
Replace the frame on the base and connect it
to the wall using screws (3.1) & (3.2).
(The wall plugs, screws and drill are not
included).
Finally connect the frame to the base.
4L and 4R. DOORS
Attention: Do not stand the assembled
door on the door gliders (1014) to avoid
damaging them.”
Push the door gliders (1014) onto both ends of
door bar (1360) (4.1).
Assemble the door as shown in diagram 4.
Connect door rollers (1015) to the door bar
(1362) using bolt (1304), washer (1009) and
nut (1007) (4.4).
Bolt door bar (1362) to upper bar (1359) (4.3)
and slide the door seal (3021) into the outside
side bar (4059) (4.5). Slide bolts (1500) into
the bottom of the bolt channel holding brush
seals (3021) and x it in place using nut (1515)
(4.6). Please ensure that for the inside side
bar, the part (4099) is used on the right in (4R)
and (4098) on the left in (4L).
EN
1. PLEASE READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE ASSEMBLING YOUR GREENHOUSE.
2. Sharp edges and corners can cause injury. Always wear protective glasses, gloves, shoes and headgear when handling the aluminium proles, glass and
polycarbonate sheets. Broken glass is a safety hazard – always clear up immediately and dispose of with care.
3.
The product you have purchased is intended only for the growing of plants and should only be used for this purpose. When used for other purposes we will
take no responsibility.
4. It is recommended that this greenhouse is assembled by two people.
5. Should you encounter difculties constructing this house, or in tting the glass or polycarbonate sheets, please contact your retailer
– do not use force!
6. The greenhouse must always be anchored.
007.01.2007

Chat med din Vitavia Ida 3300-manual ved hjelp av AI

Få umiddelbare AI-svar fra din Vitavia Ida 3300-manual

Spør hva som helst om Vitavia Ida 3300. Svarene kommer fra denne manualen, med de sidene de er basert på.

Ida 3300 Vedlikeholdsplan

Av og til
Vask drivhuset

Vask grundigt med et mildt rengøringsmiddel af og til. Sørg for, at rengøringsmidlet ikke reagerer aggressivt med aluminium eller glasfæsteklips.

Vis i manualen (side 4)
Regelmæssigt
Rengør dørskinner

Rengør øvre og nedre dørskinner regelmæssigt for at undgå ophobning af affald.

Vis i manualen (side 4)
M: QW-35-FL

Ask a Question

0/1000

Do you recommend Ida 3300?

Ja Nei

Frequently Asked Questions

A

The base must be exactly square and level. You can use a galvanized steel base (sold as an accessory) or construct a concrete/stone foundation following the manual’s dimensions. Treated timber strips (18 mm high, max 32 mm wide) are recommended between foundation and aluminium frame; fix these with 50 mm bolts. Foundations should extend below frost level.

Er dette svaret nyttig?

A

Yes. 4 mm twin-wall polycarbonate is an accepted alternative. Ensure the UV-protected side faces outward (marked by protective foil), remove the foil before installation, fit gaskets to profiles, secure panels with glazing clips, and allow space for thermal expansion because panels are cut slightly shorter on purpose.

Er dette svaret nyttig?

A

Essential tools: flat and PH2 screwdrivers, 10 mm socket or spanner, measuring stick, spirit level, knife, and an accu-drill with adjustable torque. Nuts (1002) should be tightened to a maximum torque of 3 Nm to avoid damage.

Er dette svaret nyttig?

A

Doors: fit door gliders into the bottom door profile, assemble door rollers and attach to the upper door bar, install brush seals and slide the door into the upper runner; add bolts as door stoppers and adjust for smooth movement. Roof vent: assemble side and top bars per glass thickness, insert glass, bolt the bottom bar, slide window into the ridge rail to position, then fit the window opener and fixers.

Er dette svaret nyttig?

A

Wear protective gear when handling glass. Clean the greenhouse occasionally with a mild detergent that won’t attack aluminium or clips. Keep upper and lower door tracks clear of debris. Close doors and vents in high winds, remove heavy snow from the roof, and consider heating/supporting in winter. Anchor the greenhouse and consider adding it to home insurance.

Er dette svaret nyttig?

A

No. The manual notes that wall plugs, screws for fixing to the wall, and drill bits are not included. Some accessories like the galvanized steel base are optional and sold separately; check with your retailer for these items and any region-specific fasteners.

Er dette svaret nyttig?

A

Fit glazing seals to the aluminium profiles, start glazing the roof from the eaves using glazing spring clips, overlay the next pane over the one beneath and secure retaining clips between panes, and begin side glazing from the bottom. Use washers where the glazing bars join the eaves track and follow the parts diagram for clip placement.

Er dette svaret nyttig?

M: OA-GPT-5-NAN

Advantages and Disadvantages

Advantages

  • Space-saving lean-to design ideal for attaching to a house wall, saving garden area
  • Rigid aluminium frame offering corrosion resistance and long-term durability
  • Supports 4 mm glazing (glass or polycarbonate) with specific instructions for each material
  • Integrated roof vent and adjustable sliding door system for good ventilation control
  • Comprehensive manual with parts list, diagrams and maintenance/safety guidance
VS

Disadvantages

  • Requires a precisely square, level base and careful anchoring to the wall
  • Assembly is multi-step and typically needs two people and several tools
  • Maximum nut torque limited to 3 Nm—overtightening can cause damage
  • Polycarbonate panels need correct orientation (UV side out) and allowance for expansion
  • Optional steel base and wall fixings (plugs, screws) often sold separately
M: OA-GPT-5-NAN

Produkt Spesifikasjoner

Glasering

Polykarbonat 4mm (dobbeltveggede plater)

Ramme

Aluminium

Farge

sølv

Areal

3,3m²

Spesialfunksjoner

Takvindu

Dør

Dobbel skyvedør

Dimensjoner (LxBxH)

2550x1320x2220mm

M: GO-GEM-FL-25

Produkt Beskrivelse

Vitavia Ida 3300 HKP 4mm Lean-to Greenhouse alu Manual

The Vitavia Ida 3300 HKP is a lean-to aluminium greenhouse engineered for hobby and serious gardeners who want a robust, space-efficient growing space attached to a wall. Sized to fit narrow plots and terraces, this model accepts 4 mm glazing (clear glass or twin-wall polycarbonate) and features an aluminium frame, ridge-mounted roof vent, sliding door system, and purpose-made glazing seals and clips. The manual covers site selection, required tools, foundation options, step-by-step assembly, glazing methods, door and roof-vent installation, and maintenance advice.

Assembly begins with a perfectly square, level base—either a prepared concrete/stone foundation or an optional galvanized steel base. The instructions explain aligning and loosely connecting front and side profiles, fitting corner plates, installing sill and ridge profiles, and adding extra bolts in glazing bars intended for the roof vent. Wall-anchoring is detailed: mark predrilled holes, drill 6 mm holes in the wall, insert plugs, and fasten the frame securely (max. nut torque 3 Nm).

Doors are preassembled from profiles, rollers and gliders. The manual stresses not to place assembled doors on the gliders, how to fit gliders and rollers, install brush seals and door stops, and adjust the door for smooth sliding on upper and lower tracks. The roof vent assembly explains choosing the correct side/top bars depending on glazing thickness, squaring the window, sliding it along the ridge rail to the desired position, and attaching the opener and fixers.

Glazing guidance covers both clear glass and polycarbonate. For glass, apply glazing seals to aluminium profiles, start roofing glazing at the eaves, secure panes with spring clips and retaining clips, and fit side panes from the bottom up. For polycarbonate, note the UV-protected side, remove protective film, fit gaskets and clips, and allow for thermal expansion. The manual recommends neutral silicone sealing only if desired, regular cleaning with non-aggressive detergents, and routine clearing of door tracks and roof snow.

Safety and maintenance notes run throughout: always wear protective gear when handling glass and profiles; assemble with two people; anchor the greenhouse; close vents and doors in high winds; clear heavy snow; and include the greenhouse in household insurance. A parts list and exploded diagrams aid identification and spare-part ordering.

Notes:

  • Designed primarily for plant cultivation; other uses void responsibility.
  • Max recommended nut tightening torque: 3 Nm.
  • Optional galvanized steel base recommended for exposed, windy sites.

Pros and cons are listed below to help evaluate suitability.

M: OA-GPT-5-NAN

© Copyright 2026 Manual.ly